No Category
Oil stains soak deep into the concrete’s pores. Simple washing or pressure-washing is not enough, as the oil will be pushed back to the surface later, causing problems like coating failure (blistering, peeling) or recurring dark spots. The key is a three-step process: Degrease, Poultice, and […]
No Category
maintenance, preservation
No Category
cuisine, meal
No Category
sanitation, sterilization, washing
No Category
abolish, clear away, cut out, delete, discard
No Category
Rust Bullet Concrete coatings will be fully cured within 3-5 days. Do not put heavy items on the floor during this time. If you have a vehicle with performance tires, it is recommended to wait 7-10 days before pulling onto the floor immediately after driving. Please […]
No Category
Yes, Rust Bullet Decorative Flakes make a great addition to any concrete project to enhance aesthetics. Apply Decorative Flakes when the last coat of Rust Bullet is wet. Spread the flakes on a wet coat, working in sections. Once the flakes have been spread, follow the […]
No Category
impression, scar, imprint, line, stain, stamp, spot, streak
No Category
moisture, evaporation
No Category
Optimum dry time between coats is two to six hours, not to exceed 12 hours. The previous coat should not be wet or too tacky; if there is no transfer of the coating to a gloved finger it is safe to apply an additional coat. If […]
No Category
function, operation, use
No Category
Use a mild detergent such as dish soap and water or Simple Green. Power washing is not recommended as to avoid introducing too much water to the concrete prior to application. Do not use any other type of chemical without asking Rust Bullet Technical Support. Not […]
No Category
Typically, porous floors are a good thing, up to a point, when applying any concrete coating. It enables the coating to achieve a good mechanical bond to the substrate. One thing to consider, however, is that it will reduce the coverage rate and DFT (dry film […]
No Category
engrave, imprint
No Category
Theoretical coverage is approximately 300-350 sq/ft per gallon, per coat depending on the method of application and the porosity of the surface. Generally, on a concrete surface, the first coat will take the most coating as it seeps into the pores of the concrete. The second […]
No Category
Rust Bullet coatings provide robust protection against hot tire pickup thanks to their superior durability, chemical resistance, and heat resistance. To achieve the best results, carefully follow the application guidelines, ensure proper surface preparation, and allow sufficient curing time. Regular maintenance will further extend the performance […]
No Category
cold, hot, heat, climate, conditions
No Category
Concrete sealers will prevent Rust Bullet Concrete coatings from achieving good adhesion to the surface. In most cases, the surface will need to be ground to remove this sealer and create a profile for adhesion. This can be done mechanically or by hand and a basic […]
No Category
Rust Bullet Concrete coatings are moisture sensitive. Even the smallest amount of moisture on the surface can cause a coating failure. A moisture meter, calcium chloride test, or a plastic sheet test can be conducted to check for moisture. To perform the plastic sheet test for […]
No Category
Yes. Rust Bullet Concrete coatings are easy to apply and can be used by anyone from DIY consumers to professionals. This FAQ section is a great resource if you have any questions, and as with any project, it is a good idea to review the product […]
No Category
groundwork, construction, education, precaution, prepared,
No Category
bond, adhesive, construction, groundwork, sustenance
No Category
operate, operation, use, utilization
No Category
Rust Bullet for Concrete is an industrial strength moisture-cured urethane protective coating, specially formulated for concrete applications. This is our original concrete coating, and it provides phenomenal adhesion and durability. It uses an aluminum flake in the coating which provides overlapping protection and gives it its […]
No Category
Rust Bullet, LLC has two coatings specifically designed to protect your concrete surfaces. The first is our original concrete coating, Rust Bullet for Concrete which comes in a metallic grey color. The other option is our DuraGrade Concrete line of concrete coatings, which comes in 18 […]
